DescriptionThe TRIcrimp® crimping tool was exclusively designed to provide a
positive crimp on the 15, 30 & 45 amp contacts manufactured by Anderson Power
Products for the Powerpole® line of products. It has the following features.
- Crimps all three sizes of Powerpole® contacts; 15, 30 and 45 amp
- Built-in contact positioner that holds the contact during crimping
- Ratchet mechanism assures proper crimps every time
- Far faster and better than soldering
- Provides the highest strength and the lowest resistance connections
possible
- Dimensions: 7.75" X 3" X 1.5"
- Weight: 20 ounces
- High Contact retention force
Contacts & Jaw Position
The 3 contacts have different amp ratings:
- 15 Amp (SKU: 1332) is designed to receive 16, 18 and 20 gauge wire.
- 30 Amp (SKU: 1331) is designed to receive 12, 14 gauge wire.
- 45 Amp (SKU: 261G2) is designed to receive 10 gauge wire.
The contact size corresponds to the position marking on the die. The 15 amp
contact goes into the 15 amp position, the 30 amp into the 30 position, and 45
amp into the 45 position.
Assembly Instructions 15 & 30 Amp
To crimp the 15 & 30 amp contacts it is recommended that you insert the wire
into the contact prior to inserting them into the tool. Then, with the flat side
of the contact down, insert the contact tip into the proper slot for crimping.
Squeeze the ratchet handle until the ratchet mechanism releases. Do not over
crimp by squeezing the handles together until they touch, it is possible to
break the die.
Assembly Instructions 45 Amp
To crimp the 45 amp contact it is recommended that you position the tip of
the 45 amp contact into the 45 amp position slot before the wire is inserted.
Make sure the contact is properly positioned with the U (open contact) facing
up. If the contact is lying sideways you may not obtain a proper crimp. Then,
insert your wire into the inserted contact.
Squeeze the ratchet handle until the ratchet mechanism releases. Do not over
crimp by squeezing the handles together until they touch, it is possible to
break the die.
Warranty:
The Powerwerx support policy is simple: we want you to be happy! If you have
a problem, please feel free to contact us and we will do our best to get you up
and running as soon as possible.
The TRIcrimp® has a one-year limited warranty. We will repair or replace your
TRIcrimp® if you encounter any problems within one year of purchase. We reserve
the right to charge a reasonable fee for repairing units with user-inflicted
damage. It is your responsibility to ship the defective unit back to Powerwerx.
We will pay for the replacement shipping to you. We reserve the right to upgrade
your equipment to an equivalent or better model.
TRIcrimp® is a registered trademark of Powerwerx.
Interchangeable Accessory Die Sets
This 6 die set package contains:
- Allen head wrench for die removal/installation
- Replacement screws, washer & bolt
- 6 Interchangeable accessory die sets for the
TRIcrimp tool listed blelow
TRIcrimp die sets will not fit or work with any other brand of tool
 |
 |
D-OEM
This die performs the same function as our separate
CT-OEM tool but
configured to fit the TRIcrimp handle. Crimper designed for
OEM-T
power source
and
OEM-T radio side connectors. Also works with other OEM HF/VHF connector
contacts (Powerwerx SKUs:
HF2,
HF3,
HF4,
HF6 and mating radio side
contacts). |
 |
 |
D-75
This die performs the same function as our separate
CT-75 tool but
configured to fit the TRIcrimp handle.
Crimper for 75 amp Powerpole and 50 amp SB Series contact numbers
5900,
5952 and 5915. Recommended for 6, 8 and 10 gauge contacts. Can also be
used for large solderless terminals. |
 |
 |
D-HEX
Hex crimp tool for crimping various sizes of Coaxial cable
connectors. The dies can work with but not limited to: RG- 58, 59, 62,
5, 6, 21, 140, 141, 142, 143, 210, 222, 223, 303, 304, 400, Belden 8279,
8281, 9231, 9141 |
 |
 |
D-177
Non-insulated terminals from 7 AWG to 17 AWG dies custom made to fit
the TRIcrimp handle. |
 |
 |
D-1020
Excellent for Insulated terminals from 10 AWG to 20 AWG dies custom
made to fit the TRIcrimp handle. |
 |
 |
D-2213
Excellent for Insulated terminals and end sleeves from 10 AWG- 22
AWG custom made to fit the TRIcrimp handle. |
